Hose shield 4
Designed to shield fuel lines, hoses, and cable looms from abrasion and damage. Durable high-visibility orange, simply wire-tie into place. Works on lines, hoses, and cables up to 1" in diameter. 4 inches long.
|
 |
|
|
|
Hose shield 6
Designed to shield fuel lines, hoses, and cable looms from abrasion and damage. Durable high-visibility orange, simply wire-tie into place. Works on lines, hoses, and cables up to 1" in diameter. 6 inches long.
|
|
|
|
|
Hose shield 8"
Designed to shield fuel lines, hoses, and cable looms from abrasion and damage. Durable high-visibility orange, simply wire-tie into place. Works on lines, hoses, and cables up to 1" in diameter. 8 inches long.
|
 |
|
|
|
-10 AN Aluminum Straight Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
 |
|
|
|
-10 AN Aluminum 180 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
 |
|
|
|
-10 AN Stainless Braided Hose
Fuel-resistant high-pressure hose with a stainless-steel woven covering. Accepts AN-style thread-on fittings. Sold per foot.
|
 |
|
|
|
-10 AN to 3/8" NPT Adapter
Adapts to -10AN from 3/8" NPT. Allows plumbing of fuel rails, filters, dampers, etc. Plated steel for durability and corrosion resistance.
|
|
|
|
|
-10 AN Aluminum 45 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
 |
|
|
|
-10 AN Aluminum 90 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
 |
|
|
|
-10 AN Steel Bulkhead Fitting
Bulkhead fitting is used whenever a fuel line must pass through a firewall, bulkhead, cover, etc. Plated steel for corrosion resistance.
|
 |
|
|
|
-10 AN to 18mm metric Adapter
Male-to-male fitting converts -10 AN to 18mm straight-thread. Requires a sealing washer on the metric side (sold separately). Used to convert metric fuel systems, such as those found on European vehicles, to AN braided stainless lines. Plated steel for durability and corrosion resistance.
|
|
|
|
|
12mm Washer Seal
Rubber-coated steel washer used with 12mm straight-thread fittings. Sold individually.
|
|
|
|
|
14mm Washer Seal
Rubber-coated steel washer used with 14mm straight-thread fittings. Sold individually.
|
|
|
|
|
18mm Washer Seal
Rubber-coated steel washer used with 18mm straight-thread fittings. Sold individually.
|
|
|
|
|
-4 AN Steel Straight Hose Fitting
Reusable hose fitting for use with braided stainless AN line. Sold individually.
|
 |
|
|
|
-4 AN Steel Bulkhead Fitting
Bulkhead fitting is used whenever a fuel line must pass through a firewall, bulkhead, cover, etc. Plated steel for corrosion resistance.
|
|
|
|
|
-4 AN Stainless Braided Hose
Fuel-resistant high-pressure hose with a stainless-steel woven covering. Accepts AN-style thread-on fittings. Sold per foot.
|
|
|
|
|
EFI Fuel Return Kit
This kit allows a fuel return system to be added to vehicles not originally equipped with one, such as when converting carbureted vehicles to EFI. Simply install the adapter, then run a return line to the vehicle's fuel filler neck. Adapter features a A 3/8" hose barb for ease of installation. Will fit most filler necks with a 2" outside diameter.
|
 |
|
|
|
-6 AN Aluminum Straight Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-6 AN Steel Bulkhead Fitting
Bulkhead fitting is used whenever a fuel line must pass through a firewall, bulkhead, cover, etc. Plated steel for corrosion resistance.
|
|
|
|
|
-6 AN Aluminum 180 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-6 AN Stainless Braided Hose
Fuel-resistant high-pressure hose with a stainless-steel woven covering. Accepts AN-style thread-on fittings. Sold per foot.
|
|
|
|
|
-6 AN to 3/8 NPT adapter
Adapts to -6AN from 3/8" NPT. Allows plumbing of fuel rails, filters, dampers, etc. Plated steel for durability and corrosion resistance.
|
 |
|
|
|
-6 AN Aluminum 45 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
Tee fitting for Pulsation Damper (-6AN)
Allows the Marren Pulsation Damper to be installed on the end of a fuel rail. 3/8" NPT inlet from fuel line and outlet to dampener with a -6AN pressure regulator feed line.
|
 |
|
|
|
Tee fitting for Pulsation Damper (-8AN)
Tee fitting has two male 3/8" NPT ends with a single -8 AN outlet between them. Used for mounting dampers, fuel pressure regulators, etc. Plated steel for durability and corrosion resistance.
|
 |
|
|
|
-6 AN Aluminum 90 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-6 AN to 12mm metric Adapter
Male-to-male fitting converts -6 AN to 12mm straight-thread. Requires a sealing washer on the metric side (sold separately). Used to convert metric fuel systems, such as those found on European vehicles, to AN braided stainless lines. Plated steel for durability and corrosion resistance.
|
|
|
|
|
-8 AN Aluminum Straight Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-8 AN Steel Bulkhead Fitting
Bulkhead fitting is used whenever a fuel line must pass through a firewall, bulkhead, cover, etc. Plated steel for corrosion resistance.
|
|
|
|
|
-8 AN Aluminum 180 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-8 AN Stainless Braided Hose
Fuel-resistant high-pressure hose with a stainless-steel woven covering. Accepts AN-style thread-on fittings. Sold per foot.
|
|
|
|
|
-8 AN to 3/8 NPT adapter
Adapts to -8AN from 3/8" NPT. Allows plumbing of fuel rails, filters, dampers, etc. Plated steel for durability and corrosion resistance.
|
 |
|
|
|
-8 AN Aluminum 45 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-8 AN Aluminum 90 Degree Hose Fitting
Reusable aluminum hose fitting for use with braided stainless AN line. Swivel fitting can be adjusted after assembly. Made from aircraft-quality anodized aluminum for corrosion protection. Sold individually.
|
|
|
|
|
-8 AN to 12mm metric Adapter
Male-to-male fitting converts -8 AN to 12mm straight-thread. Requires a sealing washer on the metric side (sold separately). Used to convert metric fuel systems, such as those found on European vehicles, to AN braided stainless lines. Plated steel for durability and corrosion resistance.
|
|
|
|
|
-8 AN to 14mm metric Adapter
Male-to-male fitting converts -8 AN to 14mm straight-thread. Requires a sealing washer on the metric side (sold separately). Used to convert metric fuel systems, such as those found on European vehicles, to AN braided stainless lines. Plated steel for durability and corrosion resistance.
|
|
|
|
|
-8 AN to 18mm metric Adapter
Male-to-male fitting converts -8 AN to 18mm straight-thread. Requires a sealing washer on the metric side (sold separately). Used to convert metric fuel systems, such as those found on European vehicles, to AN braided stainless lines. Plated steel for durability and corrosion resistance.
|
|
|
|
|
Fuel pressure gauge, 1.5" rear inlet
A pressure gauge designed to be permanently mounted in the fuel system. Fuel resistant, measures 0-100 PSI. 1/8" NPT male inlet on the rear of the gauge. This gauge may be permanently installed on the Marren Fuel Damper p/n 0201 or Billet Fuel Pressure Regulator p/n 0612.
|
 |
|
|
|
Fuel pressure gauge, 1.5" side inlet
A pressure gauge designed to be permanently mounted in the fuel system. Fuel resistant, measures 0-100 PSI. 1/8" NPT male inlet on the side (bottom) of the gauge. This gauge may be permanently installed on the Marren Fuel Damper p/n 0201 or Billet Fuel Pressure Regulator p/n 0612.
|
 |
|
|
|
Fuel pressure gauge, 2", side inlet
A pressure gauge designed to be permanently mounted in the fuel system. Fuel resistant, measures 0-100 PSI. 1/4" NPT male inlet on the side (bottom) of the gauge. May be installed anywhere a 1/4" NPT female port is available.
|
 |
|
|
|
